SIFAT PEMESINAN EMPAT JENIS KAYU KURANG DIKENAL DAN HUBUNGANNYA DENGAN BERAT JENIS SERTA UKURAN PORI
Abstract
The machining properties of four lesser known wood species from natural forest in Kalimantan has been investigated. The wood species were gading (Koilodepes sp.), penjalin (Drypetes sp.), arang (Diospyros macrophylla B.) and sibau (Blumeodendron kurzii I.I Sm) with their specific gravities, i.e. 0.83, 0.81, 0.55, and 0.56, respectively. Further, assessment was conducted on the relation between wood characteristics (i.e. specificgravity and vessel diameters) and the possible occurrence of defect due to machining. The machining work included planning, shaping, boring, turning and sanding.
The results revealed that machining properties were significantly affected by wood specific and vessel diameter. The higher the specific gravity and the smaller the pore diameter, the less defect that resulted from wood machining. As such, the machining quality of gading and penjalin woods was regarded as very good. Meanwhile, the machining qualities of arang and sibau woods as good to very good. Therefore, to infer, wood with higher specific gravity tends to improve machining properties. Likewise, wood with larger vessel diameter will downgrade the machining properties.
Keywords
Full Text:
PDF (Bahasa Indonesia)References
Anonim, 1952. Nama-nama kesatuan untuk jenis-jenis pohon yang penting di Indonesia
Pengumuman Istimewa No.6. Balai Penyelidikan Kehutanan. Bogor
------, 1985. Dasar-dasar identifikasi kayu. Pusat Penelitian dan Pengembangan Hasil
Hutan. Bogor.
------, 1981. Standard Methods of Conducting Machining Test of Wood and Wood- based Materials : ASTM D 1666-64. Annual Book or ASTM Standards, part 22 : Wood; Adhesives. American Society for Testing and Materials, Philadelphia.
------, 198l. Annual Book or ASTM Standards, Part 22 : Wood; Adhesives. ASTM D
-69 (Reapproped 1977), Standars Test Methodes for Specific Gravity of
Wood-base Materials. Philadelphia
Abdurachrnan, A.J. dan S, Karnasudirdja. 1982. Silat pemesinan kayu-kayu Indonesia.
Laporan BPHH no. 160. Bogor.
Acep, U. 1997. Sifat dan kualitas pemesinan kayu jati (Tectona grandis linn.f) Serat tidak teratur pada bagian tunggak dan pertemuan cabang, Univcrsitas Winaya Mukti. Bandung.
Haygreen, J.G. and J.L. Bowyer. 1982. Hasil Hutan dan Ilmu Kayu. Terjemahan Gadjah
Mada University Press. Yogyakarta.
Mandang, YI. dan U. Sudarji. 200 I. Anatomi dan kualitas serat sembilan jenis kayu kurang dikenal asal Kalimantan Timur. Buletin Penelitian Hasil Hutan Pusat Penelitian dan Pengembangan Teknologi Hasil Hutan Bogor. 19 (1): 41 - 67
Martawijaya, A., I.. Kartasujana, K. Kadir dan S.A. Prawira. 198l. Atlas Kayu
Indonesia Jilid I. Pusat Penelitian dan Pengembangan Kehutanan . Bogor.
Mustafa, Z. 1990. Panduan Microstat untuk mengolah data statistik. Penerbit ANDI OFSET. Yogyakarta.
Rachman, O. dan J. Balfas. 1985. Sifat pemesinan 34 jenis kayu dari Maluku dan
Sulawesi Tengah. Jurnal Penelitian Hasil Hutan 2 (3). Bogor.
-------., D. Rohadi dan J. Balfas.1989. Karakter Penggergajian dan pemesinan kayu aren
(Arenga pinnata). Jurnal Penelitian Hasil Hutan 6 (3). Bogor.
Sudjana. 1975. Pengantar Statistik. PT Galia Indonesia. Jakarta.
DOI: https://doi.org/10.20886/jphh.2002.20.1.70-85
Refbacks
- There are currently no refbacks.
JURNAL PENELITIAN HASIL HUTAN INDEXED BY:
Copyright © 2015 | Jurnal Penelitian Hasil Hutan (JPHH, Journal of Forest Products Research)
eISSN : 2442-8957 pISSN : 0216-4329
JPHH is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.